[james peters]

I had a dirty gutter job yesterday, and so being as my tap water is a low tds , I filled my tank from the tap with hot water.
It stayed  warm  all day. hopefully it wont affect the resin too much!
I have to say WOW.... what a difference it made , especialy on the fascia clean .
windows seemed easier also and dried a lot faster.
today I did the same as I had some first cleans .....
however flaming nightmare using the univalve when the pole is extended!!!!!! the hose goes so soft , its hard to use the univalve !

so can you recomend your hot water pole hose of choice please?

[dazmond]

Any PU hose will do.....I use the blue exceed on my main pole and some orange stuff for my high level pole....

[jk999]

Did you check the tds of your water you was using

[james peters]

Did you check the tds of your water you was using

yes ... its around 75  from the tap and 0 after resin .
I am not  a newbie , I have been 15 years wfp and 29 yrs window cleaner
I do expect the resin to not last as long , but I may just use hot on first cleans and fascias .

[james peters]

Any PU hose will do.....I use the blue exceed on my main pole and some orange stuff for my high level pole....

cheers daz

[Splash & dash]

Gardiners green Pu is the best with virtually no stretch at all , very tough stuff

[jk999]

The reason i asked was if you test tds from tap with hot its alot higher than cold so chance s are is your resin will get used up alot quicker

[dazmond]

The reason i asked was if you test tds from tap with hot its alot higher than cold so chance s are is your resin will get used up alot quicker

I've found this to be a total myth......every time I've checked my tds its 000 no matter whether its hot or cold water

[james peters]

The reason i asked was if you test tds from tap with hot its alot higher than cold so chance s are is your resin will get used up alot quicker

you are correct.
I just tested my water.... cold was 62ppm
hot was 72ppm
TBF thats pretty low  though.     I think it is worth it for the privlege of having warm water in my tank.
i think I will insulate the tank to contain the heat

[Splash & dash]

The reason i asked was if you test tds from tap with hot its alot higher than cold so chance s are is your resin will get used up alot quicker

I've found this to be a total myth......every time I've checked my tds its 000 no matter whether its hot or cold water

No it’s true hot water will give a TDS reading then let it cool and it will read 000 , it’s something to do with the speed that hot water moves at someone did  explaine it years ago

[dazmond]

The reason i asked was if you test tds from tap with hot its alot higher than cold so chance s are is your resin will get used up alot quicker

I've found this to be a total myth......every time I've checked my tds its 000 no matter whether its hot or cold water

No it’s true hot water will give a TDS reading then let it cool and it will read 000 , it’s something to do with the speed that hot water moves at someone did  explaine it years ago

I purify my water at the end of my working day and if ive only worked half a day the remaining water is still fairly hot to touch(even with half a tank of cold pure in it!)...i always test my tds straight after fill up without fail every day and its still 000......in fact ive never had a different reading hot or cold when using dionised water......

[NWH]

James try using hot water at 60+ degrees and see what you think to that then if you thought that was better,it becomes a job of just colouring in glass when you use proper hot water like the jump from ladders to a pole when you have a good WFP technique.

[NWH]

I use the Gardiner yellow-greenish hot hose as well as the orange they do they are both very good they don’t kink with very hot water.