[NWH]

If mine plays up I might try that myself then Daz🤣🤣,maybe that’s why mine was turning off.

[P @ F]

Just looked at mine Daz , the heater on the van that is , it looks like the same holder as yours , it’s showing signs of degrading now  , I bet a £ to a pinch of poop that it’s the problem , mine took 2 attempts to fire up last Friday but I thought nothing of it at the time.

[Splash & dash]

Just looked at mine Daz , the heater on the van that is , it looks like the same holder as yours , it’s showing signs of degrading now  , I bet a £ to a pinch of poop that it’s the problem , mine took 2 attempts to fire up last Friday but I thought nothing of it at the time.

The problem is a dirty connection between the fuse and the holder and it’s not creating a good circuit and is then arching causing heat and the melting of the holder this will cause the boiler to cut out just needs the holder replacing and a squirt of electrical contact cleaner every few weeks/ months .

[NWH]

I’ll give that a go tomorrow you’ve got WFPolers thumb nail,they go like that from constantly adjusting the clamps 🤣🤣🤣 get  that myself then it grows out and comes back.

[dazmond]

cheers lads...yes richy thats the same holder as mine....ive ordered 2 from grippatank as halfords and screwfix dont sell them?or if they do i couldnt find them on their websites.....

[harleyman]

Try rs componants  or city electrical

[dazmond]

Try rs componants  or city electrical

Cheers mate....I've managed to order some bullet connectors from Amazon......rs components have a minimum order of 25 inline fuse holders....I dont need that many!

[Spruce]

Almost sounds to me like the heater needs cleaning out/ de coking if it’s not blowing the fuse.
Prob looking at two hours of windowcleaners wages to service (£200 +).

If fitting a new fuse holder and fuse doesn't solve the problem I'll get it serviced.....

Time to replace it with a new one me thinks! 

[Dave Willis]

Try and borrow a proper crimping tool too if you’re changing the bullet connectors. Most electricians would have one. They ratchet the crimp and do a proper job.

[NWH]

Mine are flat connectors not bullets I checked them today it looks fine although where it connect from inside the cabinet I can see a bit of wire before the flat crimp.

[dazmond]

Try and borrow a proper crimping tool too if you’re changing the bullet connectors. Most electricians would have one. They ratchet the crimp and do a proper job.

yep ive already got some dave.......i did have some bullet connectors too but i cant find them anywhere!ill probably find them when the ordered ones arrive!

[NWH]

Very cramped in my cabinet when I looked earlier.

[Splash & dash]

Very cramped in my cabinet when I looked earlier.

Can you post a few pictures of it Ime interested to see what it’s like compared to mine

[dazmond]

Can I re use these blue bullet connectors?the new ones I've ordered are too small!....I managed to get them off the old wire/fuse holder......

Waiting on the new fuse holders now.....they are due to be delivered by 9pm today......hope they arrive soon so i can see if this is my heater problem.....

[dazmond]

Heres mine.......yes it's better with the cover on!

[dazmond]

Mine are flat connectors not bullets I checked them today it looks fine although where it connect from inside the cabinet I can see a bit of wire before the flat crimp.

Get a bit of insulation tape round the bare wires mate ASAP and make sure they haven't come out of the crimp!(they shouldn't do).....

[Smudger]

Wheres Nigel?


Darran

[Splash & dash]

Wheres Nigel?


Darran

Hopefully taking some pictures of the inside of his  cabinet 😂😂😂

[NWH]

🤣🤣🤣 📷 📸

[Dave Willis]

Has he come out of the closet yet?