This is an advertisement
Interested In Advertising? | Contact Us Here

Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

Darren H

  • Posts: 89
Re: 2kw immersion heater
« Reply #20 on: January 26, 2018, 12:46:39 pm »
Have been i touch with heat rod all went well till she asked me what BSP i wanted ( size thread).
Could anyone give me an idea will get the flange from tool station that says 2 .5 inch.

Michael Peterson

  • Posts: 1741
Re: 2kw immersion heater
« Reply #21 on: January 26, 2018, 04:10:52 pm »
yep ive melted a plug with 3k its just not worth it, i use 4 steel pond heaters at 500w

DeLuce

  • Posts: 1153
Re: 2kw immersion heater
« Reply #22 on: January 26, 2018, 10:53:19 pm »
Have been i touch with heat rod all went well till she asked me what BSP i wanted ( size thread).
Could anyone give me an idea will get the flange from tool station that says 2 .5 inch.

Standard immersion heater 2-1/4 inch BSP thread.

The male part of the fitting that goes through the cylinder has a 2-1/4 inch BSP thread, this measures about 65.7mm diameter,

P @ F

  • Posts: 6319
Re: 2kw immersion heater
« Reply #23 on: January 27, 2018, 12:36:15 pm »
2kw is the most i would like to go , i put on a 2kw fan heater in my icebox connie the other day for only an hour and the lead and plug got rather hot , cable went spaghetti like .
I'm so lazy I'm getting tired of it !

Darren H

  • Posts: 89
Re: 2kw immersion heater
« Reply #24 on: February 13, 2018, 06:47:45 pm »
My immersion is getting fitted tomorrow.
Could anyone tell me with the mechanical flange the bit with the nipple bits on it goes inside the tank and then pull that through the drilled hole and screw the other bit to it.
Does the gasket that came with the flange go on the bit on the outside of the tank.
The immersion heater itself just has a rubber o ring on it.
Is it wise to use Pte tape and a sealant.

Thanks for any advise

paul alan

  • Posts: 1683
Re: 2kw immersion heater
« Reply #25 on: February 13, 2018, 07:40:55 pm »
My immersion is getting fitted tomorrow.
Could anyone tell me with the mechanical flange the bit with the nipple bits on it goes inside the tank and then pull that through the drilled hole and screw the other bit to it.
Does the gasket that came with the flange go on the bit on the outside of the tank.
The immersion heater itself just has a rubber o ring on it.
Is it wise to use Pte tape and a sealant.

Thanks for any advise

Washer on the inside, i bought some good quality silicone and let it go off for12-24 hours.

Never leaked.

Darren H

  • Posts: 89
Re: 2kw immersion heater
« Reply #26 on: February 13, 2018, 07:49:04 pm »
This is why it asked the question if the cardboard gasket goes on the inside the little nipples on the flange will not be able to grip on the plastic of the tank so you can tighten without holding from the inside.

paul alan

  • Posts: 1683
Re: 2kw immersion heater
« Reply #27 on: February 13, 2018, 09:43:18 pm »
Silicone will do it just fine, without the gasket.

Darren H

  • Posts: 89
Re: 2kw immersion heater
« Reply #28 on: February 13, 2018, 09:48:51 pm »
Did you use silicon on both sides

DeLuce

  • Posts: 1153
Re: 2kw immersion heater
« Reply #29 on: February 13, 2018, 10:20:02 pm »
Belt and braces. I would. No harm if you do either 👍🏼

Slacky

  • Posts: 8249
Re: 2kw immersion heater
« Reply #30 on: February 13, 2018, 10:48:03 pm »
A belt and a set of braces?

Surely you need silicone to seal it, regardless of it slipping below the waistline?

֍Winp®oClean֍

  • Posts: 1685
Re: 2kw immersion heater
« Reply #31 on: February 14, 2018, 12:04:09 am »
Nipple part fits from the inside, push the threads through the tank wall and screw the other part to it from the outside. I have never used any sealant with the flange but PTFE the actual element threads. No washer is fitted to the nipple side. You can file a flat on the side of the nipples to aid "bite" into the tank wall if you struggle to get it to grip.👍
Comfortably Numb!