Interested In Advertising? | Contact Us Here
Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

Fin Clearview

  • Posts: 929
Which set up between microbore and pole hose?
« on: September 23, 2016, 08:22:19 pm »
Just wanted to ask the www what set up you have between the above?

Ive always had a tap on the end of the 6mm microbore (with a converted female hoselock attached) and then on the end of the pole hose i have a tap connector. Ive just ordered the new aquadaptor jobby from gardiners so now going to fit a claber 6mm hose lock to the microbore and do away with the tap.


Cheers  :)


jonboywalton75

  • Posts: 2220
Re: Which set up between microbore and pole hose?
« Reply #1 on: September 23, 2016, 10:32:41 pm »
Rectus 21,male and female
Protector ball

Fin Clearview

  • Posts: 929
Re: Which set up between microbore and pole hose?
« Reply #2 on: September 23, 2016, 11:35:52 pm »
Ive never tried them, do they last long? Do they also have an end stop?


sunshine windows

  • Posts: 2361
Re: Which set up between microbore and pole hose?
« Reply #3 on: September 23, 2016, 11:37:24 pm »
Male rectus 26 with tap on hose reel,  so I have an open flow of water if needed.

Female 26 on pole hose
To climb mount fuji you must first find a path
(Swindon, Wiltshire)

www.sunshinewindowcleaning.co.uk
www.sunshinesoftwashing.co.uk

CF Facilities

  • Posts: 287
Re: Which set up between microbore and pole hose?
« Reply #4 on: September 25, 2016, 08:43:27 am »
I used to have the same but now I have a tap on hose reel with male rectus 26 with a male rectus on pole hose with end stop. This means I can disconnect with out water going everywhere.

This week I have fitted a gardiners Gooseneck valve so I don't have to hunt for my hose tap on the ground as it used to be great at hiding.  ;D

Gooseneck valve is great BTW but can't operate well if upstairs windows are off to one side too much. Works great if standing beneath the window.

Fin Clearview

  • Posts: 929
Re: Which set up between microbore and pole hose?
« Reply #5 on: September 25, 2016, 06:36:50 pm »
I used to have the same but now I have a tap on hose reel with male rectus 26 with a male rectus on pole hose with end stop. This means I can disconnect with out water going everywhere.

This week I have fitted a gardiners Gooseneck valve so I don't have to hunt for my hose tap on the ground as it used to be great at hiding.  ;D

Gooseneck valve is great BTW but can't operate well if upstairs windows are off to one side too much. Works great if standing beneath the window.

Cheers mate, think i'll go for the rectus 21. Ideally id rig my 6mm microbore to a piece of 13mm (somehow!?) and then just fit a hoselock female to male tap connector off the pole hose. This way its cheap as chips and no where near as expensive as rectus fittings.

jonboywalton75

  • Posts: 2220
Re: Which set up between microbore and pole hose?
« Reply #6 on: September 25, 2016, 07:51:34 pm »
Rectus 21,male and female
Protector ball

Plus a univalve

Re: Which set up between microbore and pole hose?
« Reply #7 on: September 25, 2016, 08:18:20 pm »
I used to have the same but now I have a tap on hose reel with male rectus 26 with a male rectus on pole hose with end stop. This means I can disconnect with out water going everywhere.

This week I have fitted a gardiners Gooseneck valve so I don't have to hunt for my hose tap on the ground as it used to be great at hiding.  ;D

Gooseneck valve is great BTW but can't operate well if upstairs windows are off to one side too much. Works great if standing beneath the window.

Cheers mate, think i'll go for the rectus 21. Ideally id rig my 6mm microbore to a piece of 13mm (somehow!?) and then just fit a hoselock female to male tap connector off the pole hose. This way its cheap as chips and no where near as expensive as rectus fittings.
You can do that Fin, just go to Cliffords in School Road , Hove. They sell barbed hose reducers in lots of sizes. I've been doing just that for years. Then drive down Portland Road towards Sackville Road junction to the Nut and Bolt Store to buy the o rings . Adapt your system and buy local from readily available parts, saves downtime and cost.  ;)

DeLuce

  • Posts: 1153
Re: Which set up between microbore and pole hose?
« Reply #8 on: September 25, 2016, 08:39:56 pm »
Why not give the Ex-ceed set up a go? It'll do away with the need for a rectus male and female fitting and protecta ball and the rectus fitting lasts longer on there set up as the connector for the pole has a protective sleeve! Imo, (although I haven't tried the Gardiner new tap.........yet) the Exceed with univalve is a near perfect set up.

Fin Clearview

  • Posts: 929
Re: Which set up between microbore and pole hose?
« Reply #9 on: September 26, 2016, 07:33:38 am »
I used to have the same but now I have a tap on hose reel with male rectus 26 with a male rectus on pole hose with end stop. This means I can disconnect with out water going everywhere.

This week I have fitted a gardiners Gooseneck valve so I don't have to hunt for my hose tap on the ground as it used to be great at hiding.  ;D

Gooseneck valve is great BTW but can't operate well if upstairs windows are off to one side too much. Works great if standing beneath the window.

Cheers mate, think i'll go for the rectus 21. Ideally id rig my 6mm microbore to a piece of 13mm (somehow!?) and then just fit a hoselock female to male tap connector off the pole hose. This way its cheap as chips and no where near as expensive as rectus fittings.
You can do that Fin, just go to Cliffords in School Road , Hove. They sell barbed hose reducers in lots of sizes. I've been doing just that for years. Then drive down Portland Road towards Sackville Road junction to the Nut and Bolt Store to buy the o rings . Adapt your system and buy local from readily available parts, saves downtime and cost.  ;)

Cheers Barry! I didn't know Clifford's stocked them either so that's something else I learnt from your reply. I'll get down there today as I've got loads of spare hoselocks so this set up seems ideal and like you said, cheap, available and tried and tested connection. Only thing that worries me is pressure blowing the hose locks apart. With the rectus fittings i think could be another option still, I've read all the other posts on wear etc but i think if you just kept them joined and added a plastic pole hose joiner a few inches from the fitting then you could just undo with that and they cost no money when they eventually break. Anyway,I owe you a brew mate! Don't think I've knowingly seen you about - what's your van etc? Fin

Fin Clearview

  • Posts: 929
Re: Which set up between microbore and pole hose?
« Reply #10 on: September 26, 2016, 07:37:46 am »
Why not give the Ex-ceed set up a go? It'll do away with the need for a rectus male and female fitting and protecta ball and the rectus fitting lasts longer on there set up as the connector for the pole has a protective sleeve! Imo, (although I haven't tried the Gardiner new tap.........yet) the Exceed with univalve is a near perfect set up.

Thanks mate will keep this as a possible second option.

Re: Which set up between microbore and pole hose?
« Reply #11 on: September 26, 2016, 10:11:12 am »
I used to have the same but now I have a tap on hose reel with male rectus 26 with a male rectus on pole hose with end stop. This means I can disconnect with out water going everywhere.

This week I have fitted a gardiners Gooseneck valve so I don't have to hunt for my hose tap on the ground as it used to be great at hiding.  ;D

Gooseneck valve is great BTW but can't operate well if upstairs windows are off to one side too much. Works great if standing beneath the window.

Cheers mate, think i'll go for the rectus 21. Ideally id rig my 6mm microbore to a piece of 13mm (somehow!?) and then just fit a hoselock female to male tap connector off the pole hose. This way its cheap as chips and no where near as expensive as rectus fittings.
You can do that Fin, just go to Cliffords in School Road , Hove. They sell barbed hose reducers in lots of sizes. I've been doing just that for years. Then drive down Portland Road towards Sackville Road junction to the Nut and Bolt Store to buy the o rings . Adapt your system and buy local from readily available parts, saves downtime and cost.  ;)

Cheers Barry! I didn't know Clifford's stocked them either so that's something else I learnt from your reply. I'll get down there today as I've got loads of spare hoselocks so this set up seems ideal and like you said, cheap, available and tried and tested connection. Only thing that worries me is pressure blowing the hose locks apart. With the rectus fittings i think could be another option still, I've read all the other posts on wear etc but i think if you just kept them joined and added a plastic pole hose joiner a few inches from the fitting then you could just undo with that and they cost no money when they eventually break. Anyway,I owe you a brew mate! Don't think I've knowingly seen you about - what's your van etc? Fin
I'm Gleam Team, white ford ranger. Say hello if you see me about.
That system worked well for me for years although I now use exceeds tubeless kit and uni valve, Simon  ;)

Fin Clearview

  • Posts: 929
Re: Which set up between microbore and pole hose?
« Reply #12 on: September 26, 2016, 08:37:09 pm »
I used to have the same but now I have a tap on hose reel with male rectus 26 with a male rectus on pole hose with end stop. This means I can disconnect with out water going everywhere.

This week I have fitted a gardiners Gooseneck valve so I don't have to hunt for my hose tap on the ground as it used to be great at hiding.  ;D

Gooseneck valve is great BTW but can't operate well if upstairs windows are off to one side too much. Works great if standing beneath the window.

Cheers mate, think i'll go for the rectus 21. Ideally id rig my 6mm microbore to a piece of 13mm (somehow!?) and then just fit a hoselock female to male tap connector off the pole hose. This way its cheap as chips and no where near as expensive as rectus fittings.
You can do that Fin, just go to Cliffords in School Road , Hove. They sell barbed hose reducers in lots of sizes. I've been doing just that for years. Then drive down Portland Road towards Sackville Road junction to the Nut and Bolt Store to buy the o rings . Adapt your system and buy local from readily available parts, saves downtime and cost.  ;)

Cheers Barry! I didn't know Clifford's stocked them either so that's something else I learnt from your reply. I'll get down there today as I've got loads of spare hoselocks so this set up seems ideal and like you said, cheap, available and tried and tested connection. Only thing that worries me is pressure blowing the hose locks apart. With the rectus fittings i think could be another option still, I've read all the other posts on wear etc but i think if you just kept them joined and added a plastic pole hose joiner a few inches from the fitting then you could just undo with that and they cost no money when they eventually break. Anyway,I owe you a brew mate! Don't think I've knowingly seen you about - what's your van etc? Fin
I'm Gleam Team, white ford ranger. Say hello if you see me about.
That system worked well for me for years although I now use exceeds tubeless kit and uni valve, Simon  ;)

Will do, nice one Simon.