Interested In Advertising? | Contact Us Here
Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

*paul_moss

  • Posts: 2961
Thermadry
« on: April 08, 2007, 05:49:08 pm »
Bought a Thermadry kit in March and used it a couple of times now but have not found a great difference in it against a normal slow speed rotary using M/S  and charley pads.

Any body got any experiences and tips for this kit or the Dry fusion kit which I know is very similar buy uses a diferent chemical mix.

It may be me just needing to spend time wih the machine, but any pointers would help.
Paul Moss  MBICSc
www.mosscleaning.co.uk
REMOVED FOR POSTING OFFENSIVE MATERIAL

Atlantic Cleaning

  • Posts: 115
Re: Thermadry
« Reply #1 on: April 08, 2007, 11:12:20 pm »
Hi Paul

I to bought a thermadry system last year. At first I could not get on with it at all, I even had Jason from Craftex come down come down and clean a carpet with it to see where I was going wrong.
Now after using it for some time I am getting very good results and am very pleased with it, I even cleaned a trashed bw in a chip shop restaurant with it the other day, the traffic lanes were black with chip fat from the kitchen, to my amazement it come up like new!!!! (It was so dirty I used 5 pads both sides to clean an area of about 30sm)

How i use it is - First light mist with MS then a really good long scrub. Wet the pad in Catalyst and squeeze as much moisture out as possible. Put the heater on and move the machine quickly over approx 15-20 sm of carpet to evenly spread the Catalyst and to heat up the pad. Move the machine back to the beginning and start the cleaning process, I move the machine back and forth then side to side, Keep an eye on the pad when it is soiled filp it over and carry on, then change the pad as and when. Once the whole carpet is done i the put a dry pad on and quickly move the dry pad over the whole carpet (20+sm) doing this i find really helps dry the carpet super quick and also pick up more dirt left behind. The trick is is to get the pad hot as possible when spreading the chemical so when you start cleaning it is hot.

I Hope this helps, I have to say I mainly use it on med to low profile carpets and am now getting very good results. I do still use HWE on about 50ish% of my work but it deffinatly has its place.

Regards

Duncan

*paul_moss

  • Posts: 2961
Re: Thermadry
« Reply #2 on: April 09, 2007, 02:05:47 pm »
Thanks for that reply Duncan.
What temp do you set the heat to.I put it ay 80 degrees but I find that the pad does not get that hot even after padding for 10 mins it only feels warm.
Paul Moss  MBICSc
www.mosscleaning.co.uk
REMOVED FOR POSTING OFFENSIVE MATERIAL

Atlantic Cleaning

  • Posts: 115
Re: Thermadry
« Reply #3 on: April 09, 2007, 07:45:56 pm »
Hi Paul,

I set my temp around 80-90 on most carpets, I am told the pad does not need to be piping hot to work well just warm.

Regards

Duncan

Derek_Walker

  • Posts: 454
Re: Thermadry
« Reply #4 on: April 10, 2007, 07:05:35 pm »
Paul, I use the dry fusion system, If a carpet is pretty bad I normally pre-spray the activator first then go over it with the pad. The pad itself does not get boiling hot, but hot enough to do the job. If you touch the drive plate when taking it off the machine it does burn. As for the finished result between Charley & thermadry etc I would not expect a huge amount of difference as they are both great systems in there own right.

*paul_moss

  • Posts: 2961
Re: Thermadry
« Reply #5 on: April 10, 2007, 07:49:23 pm »
Derek
I think the Dry Fusion cataylst is better than the Craftex one, but im told they will only sell it to you if you have their system  >:(
Paul Moss  MBICSc
www.mosscleaning.co.uk
REMOVED FOR POSTING OFFENSIVE MATERIAL

Geoff Jewkes

  • Posts: 654
Re: Thermadry
« Reply #6 on: April 10, 2007, 08:26:55 pm »
This is true ( or it was ) and you have to buy a minimum amount per year to advertise the fact that you " are a dry fusion specialist "