Interested In Advertising? | Contact Us Here
Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

Pages: [1]

www.mrgutters.co.uk

  • Posts: 871
4040 ro lack of good pressure
« on: July 27, 2006, 06:37:19 pm »
hi all

i have a 4040 ro but it seems to only fill at a rate of 1l a minute ? does anyone no how to rectify this as these normally do 2-4 l a minute?

shawn ??? ???
Logged
If a job's worth doing, it's worth doing well.

JM123

  • Posts: 2095
Re: 4040 ro lack of good pressure
« Reply #1 on: July 27, 2006, 06:39:40 pm »
what is your tap pressure - also make sure you have closed the flush valve and any prefilters and carbon blocks are in good condition.
Logged
Live life in the fast lane.......if you break down you'll freewheel further

Ballymena N.I

abacus

  • Posts: 229
Re: 4040 ro lack of good pressure
« Reply #2 on: July 27, 2006, 10:38:51 pm »
Hi shawn
as you live south check the pressure in as some water companies are dropping the pressure at night help with the leaks you may need to install a pump to bring up the pressure or if your r.o are fouling up try flushing them for a couple of hours with pure water
regards grant
Logged
A service you can count on
SAFEcontractor approved

www.mrgutters.co.uk

  • Posts: 871
Re: 4040 ro lack of good pressure
« Reply #3 on: July 27, 2006, 10:50:32 pm »
hi guys

it was in the day today that it was purifing.. but i dont have anything to measure tap pressure

where can you buy these booster pumps

shawn
Logged
If a job's worth doing, it's worth doing well.

freshwater

  • Posts: 277
Re: 4040 ro lack of good pressure
« Reply #4 on: July 27, 2006, 11:31:34 pm »
Shawn,

4040 membranrs are rated for use at 100psi, anything less and you will reduce production rate & quality. If your water pressure is below 60psi you will probably need a pump or you will need to use de-min resin by the bucket load. Go and buy a preesure gauge and connect it to you water supply.

General: A 4040 is not always the best option if you have low water pressure. A pump that will give enough flow at a high enough pressure is expensive, we sell from £400 to £700 depending on the presure/flow required. Sometimes when you have low pressure is better to go for a system using domestic 1812 membranes whic can be powerd by much smaller pumps, take a look at our ARO400 at http://www.freshwatersystems.co.uk/series_lc.htm we have tested this unit on UK cold water with an input pressure of 30psi and a input TDS 320 and acheived 1200 litres per day at 6ppm.

Logged

www.mrgutters.co.uk

  • Posts: 871
Re: 4040 ro lack of good pressure
« Reply #5 on: July 27, 2006, 11:53:17 pm »
why wont a 100 psi pump work?

shawn
Logged
If a job's worth doing, it's worth doing well.

freshwater

  • Posts: 277
Re: 4040 ro lack of good pressure
« Reply #6 on: July 28, 2006, 08:22:43 pm »
You need flow as well as pressure. If you are expecting 3 or 4 litres per min of pure you will need a minimum input of 3 times that so 12 litres per min at 100psi. The small Flojet can do 100psi but no where near 12 litres per min.
Logged

sair

  • Posts: 682
Re: 4040 ro lack of good pressure
« Reply #7 on: July 29, 2006, 07:29:23 am »
i disagree as all our van mounts which are boostered  can achieve 4-5 liters aminutes from most water presures, it just takes a little bit of thought to replicate flow rate, we have been doing this on our systems for over three years now and they work fine and we use low presure 40x40

there are various pumps on market but youll have to spend reasonable money shawn
Logged
Essentially Pure Ltd

www.mrgutters.co.uk

  • Posts: 871
Re: 4040 ro lack of good pressure
« Reply #8 on: July 29, 2006, 07:56:51 am »
hi tony

hope all is well, how to i replicate this flow rate and how much does a pump cost... ?

i used my 100psi shurflo to get the 1l a min.... but thats all it would do

shawn
Logged
If a job's worth doing, it's worth doing well.

JM123

  • Posts: 2095
Re: 4040 ro lack of good pressure
« Reply #9 on: July 29, 2006, 11:26:21 am »
you could try using the aquatec 240v 12ltr/min booster pump for the merlin from www.surecleansystems, its set at 70psi but will still give you 3/4ltrs/min pure, but as sair says pumps aren't cheap.
Logged
Live life in the fast lane.......if you break down you'll freewheel further

Ballymena N.I

sair

  • Posts: 682
Re: 4040 ro lack of good pressure
« Reply #10 on: July 29, 2006, 11:36:18 am »
shawn is it set in van or as static if van you could come down and i ll set up for you cal me monday
Logged
Essentially Pure Ltd

www.mrgutters.co.uk

  • Posts: 871
Re: 4040 ro lack of good pressure
« Reply #11 on: July 29, 2006, 02:57:15 pm »
hi mate its in the van ..

its a 40 inch with two 20 inch pre filters


shawn
Logged
If a job's worth doing, it's worth doing well.

sair

  • Posts: 682
Re: 4040 ro lack of good pressure
« Reply #12 on: July 29, 2006, 03:50:06 pm »
call me monday 07944 227635
Logged
Essentially Pure Ltd
Pages: [1]